| AMI UP001 Pillow Block Bearings | Grease Speed Rating Open/Shielded n1:2800 rpm; Accessories:Two Seals; D:210.0000 mm; B:28.00 mm; d:150.000 mm; Basic Dynamic Radial Load Rating C:88400 N; Sealed Speed Rating n3:1800 rpm; Oil Speed Rating Open/Shielded n2:3400 rpm; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:93000 N; |
| AMI UCNTPL207-22MZ2RFCW Mounted Units & Inserts | G:M 190x3; d1:170 mm; B2:110 mm; Mass withdrawal sleeve:3.42 kg; d:180 mm; G1:17 mm; Nut for removal:KM 38; Hydraulic nut:HMV 38 E; B1:105 mm; |
| AMI MUCTB205-15 Pillow Block Bearings | dk:25 mm; Basic dynamic load rating C:21.2 kN; d4 ≈:25 mm; d:17 mm; B:14 mm; w:22 mm; h1:67 mm; l3 min.:24 mm; l7 min.:22 mm; r1 min.:0.3 mm; |
| AMI UGFL310 Flange Block Bearings | Static (Cor):7725 ; Pu:551.730 kg; Weight:375 ; D:720 mm; d:470 mm; B:270 mm; B1:167 mm; Bearing designation:PLC 512-46 ; Dynamic (Cr):3712.8 kN; |
| AMI MUCFB207-20TC Flange Block Bearings | Static moment stiffness:140 N·m/mrad; Fatigue load limit Pu:1.9 kN; r1,2 min.:0.3 mm; da min.:25 mm; ra max.:0.3 mm; Attainable speed:6400 r/min; D2:43.2 mm; b:4.2 mm; Basic static load rating C0:51 kN; r3,4 min.:0.6 mm; |
| AMI UCFBL201-8MZ2B Flange Block Bearings | Pu:0.890 kN; dynamic Cr:12.660 kN; D:30 mm; Oil:9 400 min-1; static Cor:19.600 kN; d1:30 mm; d:17 mm; Grease:7 100 min-1; D1:18 mm; rs (min):0.3 mm; |
| AMI UCFL205-16TC Mounted Units & Inserts | Grease Speed Rating Open/Shielded n1:1200 rpm; Basic Static Radial Load Rating Co:500000 N; Fillet Radius ra:3.00 mm; B:74.00 mm; Oil Speed Rating Open/Shielded n2:1500 rpm; Basic Dynamic Radial Load Rating C:358000 N; d:300.000 mm; Accessories:Two Seals & Snap-Rin; Sealed Speed Rating n3:780 rpm; D:460.0000 mm; |
| AMI UEF207 Flange Block Bearings | H2:53.975 mm; End plug (suffix Y):EPR 14; S:4.763 mm; Max. speed for PosiTrac Plus seal:1350 r/min; RG:1/2 NPT; Stabilizing ring:SR-24-20; Cap bolt recommended tightening torque:400 N·m; Cap bolt:2 x 1-8 UNC; Housing:SAF 524; R2:30.163 mm; |
| AMI UEP207-23NP Pillow Block Bearings | Limiting value e:0.2; r1,2 min.:2 mm; Da max.:108 mm; Calculation factor kr:0.23; Limiting speed:10000 r/min; Axial load factor Y:0.6; Fatigue load limit Pu:14.6 kN; r3,4 min.:2 mm; Mass bearing:1.88 kg; ra max.:2 mm; |
| AMI MUCNFL210-31B Flange Block Bearings | B:8 mm; Tolerance housing:H7; Specific dynamic load factor K:10 N/mm²; Specific static load factor K0:20 N/mm²; Permissible sliding velocity v max.:5 m/s; D:7 mm; Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ min.:0.05; Coefficient of friction µ max.:0.1; d:4 mm; |